RADCO'S
IAS ACCREDITATION SCOPE |
[download
pdf] |
Physical/Structural/Materials |
ASTM A74 |
Cast Iron Soil Pipe and Fittings |
ASTM A126 |
Gray Iron Castings for Valves, Flanges,
and Pipe Fittings |
ASTM A438 |
Transverse Testing of Gray Cast Iron
(Withdrawn 2003) |
ASTM A792 |
Steel Sheet, 55% Aluminum-Zinc Alloy-Coated
by the Hot-Dip Process |
ASTM B117 |
Operating Salt Spray (Fog) Apparatus |
ASTM B306 |
Copper Drainage Tube (DWV) |
ASTM C67 |
Sampling and Testing Brick and Structural
Clay Tile |
ASTM C97 |
Absorption and Bulk Specific Gravity
of Dimension Stone |
ASTM C109 |
Compressive Strength of Hydraulic Cement
Mortars(Using 2-in. or [50-mm] Cube Specimens) |
ASTM C190 |
Tensile Strength of Hydraulic Cement
Mortars |
ASTM C203 |
Breaking Load and Flexural Properties
of Block-Type Thermal Insulation |
ASTM C209 |
Standard Test Methods for Cellulosic
Fiber Insulating Board |
ASTM C271 |
Density of Sandwich Core Materials |
ASTM C272 |
Water Absorption of Core Materials for
Structural Sandwich Constructions |
ASTM C273 |
Shear Properties of Sandwich Core Materials |
ASTM C282 |
Acid Resistance of Porcelain Enamels
(Citric Acid Spot Test) |
ASTM C296 |
Standard Specification for Asbestos-Cement
Pressure Pipe |
ASTM C297 |
Flatwise Tensile Strength of Sandwich
Constructions |
ASTM C303 |
Dimensions and Density of Preformed
Block and Broad-Type Thermal Insulation |
ASTM C348 |
Flexural Strength of Hydraulic-Cement
Mortars |
ASTM C365 |
Flatwise Compressive Properties of Sandwich
Cores |
ASTM C393 |
Core Shear Properties of Sandwich Constructions
by Beam Flexure |
ASTM C473 |
Physical Testing of Gypsum Panel Products |
ASTM C481 |
Laboratory Aging of Sandwich Constructions |
ASTM C482 |
Bond Strength of Ceramic Tile to Portland
Cement |
ASTM C518 |
Steady-State Thermal Transmission Properties
by Means of the Heat Flow Meter Apparatus |
ASTM C564 |
Rubber Gaskets for Cast Iron Soil Pipe
and Fittings |
ASTM C567 |
Determining Density of Structural Lightweight
Concrete |
ASTM C578 |
Rigid, Cellular Polystyrene Thermal
Insulation |
ASTM C591 |
Standard Specification for Unfaced Preformed
Rigid Cellular Polyisocyanurate Thermal Insulation |
ASTM C794 |
Adhesion-in-Peel of Elastomeric Joint
Sealants |
ASTM C1289 |
Standard Specification for Faced Rigid
Cellular Polyisocyanurate Thermal Insulation Board |
ASTM C1386 |
Precast Autoclaved Aerated Concrete
(PAAC) Wall Construction Units |
ASTM D146 |
Sampling and Testing Bitumen-Saturated
Felts and Woven Fabrics for Roofing and Waterproofing |
ASTM D226 |
Asphalt-Saturated Organic Felt Used
in Roofing and Waterproofing |
ASTM D256 |
Determining the Izod Pendulum Impact
Resistance of Plastics |
ASTM D380 |
Standard Test Methods for Rubber Hose |
ASTM D412 |
Vulcanized Rubber and Thermoplastic
Elastomers - Tension |
ASTM D471 |
Rubber Property-Effect of Liquids |
ASTM D570 |
Water Absorption of Plastics |
ASTM D572 |
Rubber-Deterioration by Heat and Oxygen |
ASTM D618 |
Conditioning Plastics for Testing |
ASTM D624 |
Tear Strength of Conventional Vulcanized
Rubber and Thermoplastic Elastomers |
ASTM D638 |
Tensile Properties of Plastics |
ASTM D648 |
Deflection Temperature of Plastics Under
Flexural Load in the Edgewise Position |
ASTM D696 |
Coefficient of Linear Thermal Expansion
of Plastics Between -30°C and 30°C with a Vitreous Silica Dilatometer |
ASTM D751 |
Standard Test Methods for Coated Fabrics |
ASTM D756 |
Determination of Weight and Shape Changes
of Plastics Under Accelerated Service Conditions (Withdrawn 1998) |
ASTM D779 |
Water Resistance of Paper, Paperboard,
and Other Sheet Materials by the Dry Indicator |
ASTM D781 |
Puncture and Stiffness of Paperboard,
Corrugated and Solid Fiberboard (Withdrawn 1984) |
ASTM D790 |
Flexural Properties of Unreinforced
and Reinforced Plastics and Electrical Insulating Materials |
ASTM D792 |
Density and Specific Gravity (Relative
Density) of Plastics by Displacement |
ASTM D816 |
Standard Test Methods for Rubber Cements |
ASTM D828 |
Tensile Properties of Paper and Paperboard
Using Constant-Rate-of-Elongation Apparatus |
ASTM D882 |
Tensile Properties of Thin Plastic Sheeting |
ASTM D896 |
Resistance of Adhesive Bonds to Chemical
Reagents |
ASTM D903 |
Peel or Stripping Strength of Adhesive
Bonds |
ASTM D905 |
Strength Properties of Adhesive Bonds
in Shear by Compression Loading |
ASTM D1002 |
Apparent Shear Strength of Single-Lap-Joint
Adhesively Bonded Metal Specimens by Tension Loading |
ASTM D1037 |
Evaluating Properties of Wood-Base Fiber
and Particle Panel Materials |
ASTM D1042 |
Linear Dimensional Changes of Plastics
Under Accelerated Service Conditions |
ASTM D1183 |
Practices for Resistance of Adhesives
to Cyclic Laboratory Aging Conditions |
ASTM D1204 |
Linear Dimensional Changes of Nonrigid
Thermoplastic Sheeting or Film at Elevated Temperature |
ASTM D1212 |
Measurement of Wet Film Thickness of
Organic Coatings |
ASTM D1248 |
Polyethylene Plastics Extrusion Materials
For Wire and Cable |
ASTM D1333 |
Testing Elastic Fabrics (Withdrawn 1959) |
ASTM D1435 |
Outdoor Weathering of Plastics |
ASTM D1499 |
Filtered Open-Flame Carbon-Arc Type
Exposures of Plastics |
ASTM D1527 |
Acrylonitrile-Butadiene-Styrene (ABS)
Plastic Pipe, Schedules 40 and 80 |
ASTM D1621 |
Compressive Properties of Rigid Cellular
Plastics |
ASTM D1622 |
Apparent Density of Rigid Cellular Plastics |
ASTM D1623 |
Tensile And Tensile Adhesion Properties
of Rigid Cellular Plastics |
ASTM D1682 |
Breaking Load and Elongation of Textile
Fabrics (Withdrawn 1991) |
ASTM D1761 |
Mechanical Fasteners in Wood |
ASTM D1784 |
Rigid Poly(Vinyl Chloride) (PVC) Compounds
and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
ASTM D1785 |
Poly(Vinyl Chloride) (PVC) Plastic Pipe,
Schedules 40, 80, and 120 |
ASTM D1788 |
Rigid Acrylonitrile-Butadiene-Styrene
(ABS) Plastics (Withdrawn 1988) |
ASTM D1876 |
Peel Resistance of Adhesives (T-Peel
Test) |
ASTM D1938 |
Tear-Propagation Resistance (Trouser
Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method |
ASTM D1970 |
Self-Adhering Polymer Modified Bituminous
Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection |
ASTM D2126 |
Response of Rigid Cellular Plastics
to Thermal and Humid Aging |
ASTM D2126 |
Response of Rigid Cellular Plastics
to Thermal and Humid Aging |
ASTM D2239 |
Polyethylene (PE) Plastic Pipe (SIDR-PR)
Based on Controlled Inside Diameter |
ASTM D2241 |
Poly(Vinyl Chloride) (PVC) Pressure-Rated
Pipe (SDR Series) |
ASTM D2247 |
Testing Water Resistance of Coatings
in 100% Relative Humidity |
ASTM D2261 |
Tearing Strength of Fabrics by the Tongue
(Single Rip) Procedure |
ASTM D2282 |
Acrylonitrile-Butadiene-Styrene (ABS)
Plastic Pipe (SDR-PR) |
ASTM D2294 |
Creep Properties of Adhesives in Shear
by Tension Loading (Metal-to-Metal) |
ASTM D2299 |
Recommended Determining Relative Stain
Resistance of Plastics (Withdrawn 1992) |
ASTM D2464 |
Threaded Poly(Vinyl Chloride) (PVC)
Plastic Pipe Fittings, Schedule 8 |
ASTM D2466 |
Poly(Vinyl Chloride) (PVC) Plastic Pipe
Fittings, Schedule 40 |
ASTM D2467 |
Poly(Vinyl Chloride) (PVC) Plastic Pipe
Fittings, Schedule 80 |
ASTM D2468 |
Acrylonitrile-Butadiene-Styrene (ABS)
Plastic Pipe Fittings, Schedule 40 (Withdrawn 2003) |
ASTM D2523 |
Testing Load-Strain Properties of Roofing
Membranes |
ASTM D2581 |
Polybutylene (PB) Plastics Molding and
Extrusion Materials |
ASTM D2609 |
Plastic Insert Fittings for Polyethylene
(PE) Plastic Pipe |
ASTM D2661 |
Drain, Waste, and Vent (DWV) Pipe and
Fittings |
ASTM D2662 |
Polybutylene (PB) Plastic Pipe (SIDR-PR)
Based on Controlled Inside Diameter (Withdrawn 2003) |
ASTM D2666 |
Polybutylene (PB) Plastic Tubing (Withdrawn
2005) |
ASTM D2737 |
Polyethylene (PE) Plastic Tubing |
ASTM D2751 |
Acrylonitrile-Butadiene-Styrene (ABS)
Sewer Pipe and Fittings |
ASTM D2842 |
Water Absorption of Rigid Cellular Plastics |
ASTM D2846 |
Chlorinated Poly (Vinyl Chloride) (CPVC)
Plastic Hot- and Cold-Water Distribution Systems |
ASTM D2863 |
Measuring the Minimum Oxygen Concentration
to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D3034 |
Type PSM Poly(Vinyl Chloride) (PVC)
Sewer Pipe and Fittings |
ASTM D3309 |
Polybutylene (PB) Plastic Hot- and Cold-Water
Distribution Systems |
ASTM D3311 |
Drain, Waste, and Vent (DWV) Plastic
Fittings Patterns |
ASTM D3330 |
Peel Adhesion of Pressure-Sensitive
Tape |
ASTM D3350 |
Polyethylene Plastics Pipe and Fittings
Materials |
ASTM D3679 |
Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D3930 |
Adhesives for Wood-Based Materials for
Construction of Manufactured Homes |
ASTM D3965 |
Rigid Acrylonitrile-Butadiene-Styrene
(ABS) Materials for Pipe and Fittings |
ASTM D4226 |
Impact Resistance of Rigid Poly(Vinyl
Chloride) (PVC) Building Products |
ASTM D4317 |
Polyvinyl Acetate-Based Emulsion Adhesives |
ASTM D4396 |
Rigid Poly(Vinyl Chloride) (PVC) and
Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe
and Fittings |
ASTM D4477 |
Rigid (Unplasticized) Poly(Vinyl Chloride)
(PVC) Soffit |
ASTM D4869 |
Asphalt-Saturated Organic Felt Underlayment
Used in Steep Slope Roofing |
ASTM D5034 |
Breaking Strength and Elongation of
Textile Fabrics (Grab Test) |
ASTM D5147 |
Sampling and Testing Modified Bituminous
Sheet Material |
ASTM D5206 |
Windload Resistance of Rigid Plastic
Siding |
ASTM D5420 |
Impact Resistance of Flat, Rigid Plastic
Specimen by Means of a Striker Impacted by a Falling Weight (Gardner
Impact) |
ASTM D5456 |
Evaluation of Structural Composite Lumber
Products |
ASTM D5733 |
Tearing Strength of Nonwoven Fabrics
by the Trapezoid Procedure |
ASTM D5764 |
Evaluating Dowel-Bearing Strength of
Wood and Wood-Base Products |
ASTM D6117 |
Mechanical Fasteners In Plastic Lumber
and Shapes |
ASTM D6662 |
Polyolefin-Based Plastic Lumber Decking
Board |
ASTM D6817 |
Standard Specification for Rigid Cellular
Polystyrene Geofoam |
ASTM E8 |
Tension Testing of Metallic Materials |
ASTM E72 |
Conducting Strength Panels for Building
Construction |
ASTM E96 |
Water Vapor Transmission of Materials |
ASTM E283 |
Determining Rate of Air Leakage Through
Exterior Windows, Curtain Walls, and Doors |
ASTM E330 |
Structural Performance of Exterior Windows,
Curtain Walls, and Doors by Uniform Static Air Pressure Difference |
ASTM E331 |
Water Penetration of Exterior Windows,
Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure
Difference |
ASTM E488 |
Strength of Anchors in Concrete and
Masonry Elements |
ASTM E529 |
Guide for Conducting Flexural Tests
on Beams and Girders for Building Construction |
ASTM E547 |
Water Penetration of Exterior Windows,
Skylights, Doors, and Curtain Walls by Cyclic Static Air Pressure
Difference |
ASTM E661 |
Performance of Wood and Wood-Based Floor
and Roof Sheathing Under Concentrated Static and Impact Loads |
ASTM E695 |
Measuring Relative Resistance of Wall,
Floor, and Roof Construction to Impact Loading |
ASTM E1190 |
Strength of Power-Actuated Fasteners
Installed in Structural Members |
ASTM E1233 |
Structural Performance of Exterior Windows,
Doors, Skylights, and Curtain Walls by Cyclic Air Pressure Differential |
ASTM E1333 |
Determining Formaldehyde Concentrations
in Air and Emission Rates from Wood Products Using a Large Chamber |
ASTM E1512 |
Testing Bond Performance of Bonded Anchors |
ASTM E1677 |
Standard Specification for an Air Retarder
(AR) Material or System for Low-Rise Framed Building Walls |
ASTM E2098 |
Determining Tensile Breaking Strength
of Glass Fiber Reinforcing Mesh for Use in Class PB EIFS |
ASTM E2134 |
Evaluating the Tensile-Adhesion Performance
of an Exterior Insulation and Finish System (EIFS) |
ASTM E2273 |
Determining the Drainage Efficiency
of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies |
ASTM E2485 |
Freeze/Thaw Resistance of Exterior Insulation
and Finish Systems (EIFS) and Water Resistive Barrier Coatings |
ASTM E2486 |
Impact Resistance of Class PB and PI
Exterior Insulation and Finish Systems (EIFS) |
ASTM E2568 |
Standard Specification for PB Exterior
Insulation and Finish Systems |
ASTM F409 |
Thermoplastic Accessible and Replaceable
Plastic Tube and Tubular Fittings |
ASTM F438 |
Socket-Type Chlorinated Poly(Vinyl Chloride)
(CPVC) Plastic Pipe Fittings, Schedule 40 |
ASTM F439 |
Chlorinated Poly (Vinyl Chloride) (CPVC)
Plastic Pipe Fittings, Schedule 80 |
ASTM F441 |
Chlorinated Poly(Vinyl Chloride) (CPVC)
Plastic Pipe, Schedules 40 and 80 |
ASTM F628 |
Acrylonitrile-Butadiene-Styrene (ABS)
Schedule 40, Plastic Drain, Waste, and Vent Pipe With a Cellular
Core |
ASTM F789 |
Type PS-46 and Type PS-115 Poly(Vinyl
Chloride) (PVC) Plastic Gravity Flow Sewer Pipe and Fittings |
ASTM F810 |
Smoothwall Polyethylene (PE) Pipe for
Use in Drainage and Waste Disposal Absorption Fields |
ASTM F845 |
Plastic Insert Fittings for Polybutylene
(PB) Tubing |
ASTM F876 |
Crosslinked Polyethylene (PEX) Tubing |
ASTM F877 |
Crosslinked Polyethylene (PEX) Plastic
Hot- and Cold-Water Distribution Systems |
ASTM F891 |
Coextruded Poly(Vinyl Chloride) (PVC)
Plastic Pipe With a Cellular Core |
ASTM F949 |
Poly(Vinyl Chloride) (PVC) Corrugated
Sewer Pipe With a Smooth Interior and Fittings |
ASTM F1281 |
Crosslinked Polyethylene/Aluminum/Crosslinked
Polyethylene (PEX-AL-PEX) Pressure Pipe |
ASTM F1282 |
Polyethylene/Aluminum/Polyethylene (PE-AL-PE)
Composite Pressure Pipe |
ASTM F1575 |
Determining Bending Yield Moment of
Nails |
ASTM F1667 |
Driven Fasteners: Nails, Spikes, and
Staples |
ASTM G21 |
Determining Resistance of Synthetic
Polymeric Materials to Fungi |
ASTM G152 |
Operating Light-Exposure Apparatus (Carbon-Arc
Type) with and without Water for Nonmetallic Materials |
ASTM G155 |
Operating Xenon Arc Light Apparatus
for Exposure of Non-Metallic Materials |
ASTM G154 |
Operating Light- and Water-Exposure
Apparatus (Fluorescent UV-Condensation Type) for Nonmetallic Materials |
AC01 |
Acceptance Criteria for Expansion Anchors
in Masonry Elements (Section 5.0) |
AC04 |
Acceptance Criteria for Sandwich Panels
(Section 4.0) |
AC07 |
Acceptance Criteria for Special Roofing
Systems (Sections 3.0, 4.0, 4.5, 4.7, 4.8 & 4.9) |
AC11 |
Acceptance Criteria for Cementitious
Exterior Wall Coatings (Sections 4.1, 4.2 & 4.3) |
AC16 |
Acceptance Criteria for Plastic Glazed
Skylights (Sections A3.5, A3.9, A4.2, A4.3, A4.4, Burning Brand
Only) |
AC38 |
Acceptance Criteria for Water-resistive
Barriers (Sections 3.0 and 4.0) |
AC48 |
Acceptance Criteria for Roof Underlayment
for Use in Severe Climate Areas (Sections 3.0 and 4.0) |
AC51 |
Acceptance Criteria for Precast Stone
Veneer (Section 4.6) |
AC58 |
Acceptance Criteria for Adhesive Anchors
in Masonry Elements (Section 4.0) |
AC59 |
Acceptance Criteria for Direct-applied
Exterior Finish Systems (DEFS) (Sections 3.1.2.1, 3.1.2.3, 3.1.2.7,
5.2, 5.3, and 5.4.3; Flexural test, water absorption, freeze-thaw,
bond test, and environmental cycling only) |
AC70 |
Acceptance Criteria for Fasteners Power-driven
into Concrete, Steel and Masonry Elements (Section 4.0) |
AC106 |
Acceptance Criteria for Predrilled Fasteners
(Screw Anchors) in Masonry (Section 4.0) |
AC180 |
Acceptance Criteria for Clay and Concrete
Roof Tiles (Section 3.4 Uplift bend test only) |
AC193 |
Acceptance Criteria for Mechanical Anchors
in Concrete Elements (Tables 4.1 and 4.2) |
AC212 |
Acceptance Criteria for Water-resistive
Coatings Used as Water-resistive Barriers over Exterior Sheathing
(Sections 3.0 and 4.0) |
AC308 |
Acceptance Criteria for Post-installed
Adhesive Anchors in Concrete Elements [Except Section 8.16- Table
4.2 (Test 5), 4.3 (Test 5), and 4.4 (except Test 5); Section 9.12-
Table 4.2 (Test 17), 4.3 (Test 17), and 4.4 (except Test 16); Section
9.13- Table 4.2 (Test 18), 4.3 (Test 18), and 4.4 (except Test 17)] |
AC310 |
Acceptance Criteria for Water-resistive
Membranes Factory-bonded to Wood-based Structural
Sheathing, Used as Water-resistive Barriers (Section 4.0) |
AC358 |
Acceptance Criteria for Helical Foundation
Systems and Devices (Section 4.0) |
AC394 |
Acceptance Criteria for Structural Capacity
of Components of Work Cages for Wind Turbine Towers (Section 3.0) |
UBC 14-1 |
Kraft Waterproof Building Paper |
UBC 14-2 |
Vinyl Siding |
UBC 15-2 |
Test Standard for Determining the Fire
Retardancy of Roof Assemblies |
UBC 15-5 |
Roof Tile |
UBC 15-6 |
Modified Bitumen, Thermoplastic and
Thermoset Membranes Used for Roof Coverings |
UBC 21-6 |
In-place Masonry Shear Tests |
UBC 21-7 |
Tests of Anchors in Unreinforced Masonry
Walls |
ANSI/AAMA 711 |
Voluntary Specification for Self-Adhering
Flashing Used for Installation of Exterior Wall Fenestration Products |
ANSI/AAMA 1402 |
Standard Specifications for Aluminum
Siding Soffit and Fascia |
CAN/CSGB 41.24 |
Rigid Vinyl Siding, Soffits and Fascia |
CAN/CSGB 51.26-M86 |
Thermal Insulation Urethane and Isocyanurate,
Boards, Faced |
CAN/CSGB 51.32-M77 |
Sheathing, Membrane, Breather Type |
CAN ULC-S701 |
Standard for Thermal Insulation, Polystyrene,
Boards and Pipe Covering |
AS/NZS 4256 |
Plastic roof and wall cladding materials
- Unplasticized polyvinyl chloride (uPVC) wall cladding boards |
AS/NZS 4257 |
Plastic roof and wall cladding materials
- Methods of test - Determination of surface distortion (oil canning) |
Wood |
ASTM D3345 |
Laboratory Evaluation of Wood and Other
Cellulosic Materials for Resistance to Termites |
AWPA E1 |
Standard Method for Laboratory Evaluation
to Determine Resistance to Subterranean Termites |
Fire Testing |
API Standard 607-85 |
Fire Test for Soft-Seated Quarter Turn
Valves |
ASTM D635 |
Rate of Burning and/or Extent and Time
of Burning of Plastics in a Horizontal Position |
NFPA 33 |
Standard for Spray Application Using
Flammable or Combustible Materials |
NFPA 85 |
Boiler and Combustion Systems Hazards
Code |
NFPA 86 |
Standard for Ovens and Furnaces |
NFPA 160 |
Standard for the Flame Effects Before
an Audience |
NFPA 1123 |
Code for Fireworks Display |
NFPA 1126 |
Standard for the Use of Pyrotechnics
Before a Proximate Audience |
UBC 2-1 |
Noncombustible Material - Tests |
Electrical Testing
|
UL 197 |
Commercial Electric Cooking Appliances |
UL 307A |
Liquid Fuel-Burning Heating Appliances
for Manufactured Homes and Recreational Vehicles |
UL 508A |
Industrial control panels |
NFPA 79 |
Electrical standard for industrial machinery
(In laboratory or In-situ evaluation by designated personnel only |
UL 795 |
Commercial-Industrial Gas Heating Equipment |
Equipment |
UL 103 |
Factory-Built Chimneys for Residential
Type and Building Heating Appliances |
UL 127 |
Factory-Built Fireplaces |
UL 181 |
Factory-Made Air Ducts and Air Connectors |
UL 197 |
Commercial Electric Cooking Appliances |
UL 234 |
Low Voltage Lighting Fixtures for Use
in Recreational Vehicles |
UL 295 |
Commercial-Industrial Gas Burners |
UL 307A |
Liquid Fuel-Burning Heating Appliances
for Manufactured Homes and Recreational Vehicles |
UL 307B |
Gas-Burning Heating Appliances for Manufactured
Homes and Recreational Vehicles |
UL 311 |
Safety for Roof Jacks for Manufactured
Homes and Recreational Vehicles |
UL 441 |
Gas Vents |
UL 471 |
Commercial Refrigerators and Freezers |
UL 737 |
Fireplace Stoves |
UL 795 |
Commercial-Industrial Gas Heating Equipment |
UL 1046 |
Grease Filters for Exhaust Ducts |
UL 1075 |
Gas-Fired Cooking Appliances for Recreational
Vehicles |
UL 1083 |
Household Electric Skillets and Frying-Type
Appliances |
UL 1091 |
Butterfly Valves for Fire-Protection
Service |
UL 1995 |
Heating and Cooling Equipment |
UBC 26-3 |
Room Fire Test Standard for Interior
of Foam Plastic Systems |
ANSI A112.1.2 |
Air Gaps In Plumbing Systems (For Plumbing
Fixtures and Water-Connected Receptors) |
ANSI A112.14.1 |
Backwater Valves |
ANSI/ASME A112.19.1M |
Enameled Cast Iron and Steel Plumbing
Fixtures |
ANSI/ASME A112.19.4M |
Porcelain Enameled Formed Steel Plumbing
Fixtures |
ANSI/ASME A112.19.5 |
Trim for Water-Closet Bowls, Tanks,
and Urinals |
ANSI/ASME A112.19.7M |
Whirlpool Bathtub Appliances |
ANSI/ASME A112.19.9M |
Non-Vitreous Ceramic Plumbing Fixtures |
ANSI/ASME A112.21.1M |
Floor Drains (Replaced with ANSI/ASME
A112.6.3-2001 Floor and Trench Drains) |
ANSI/ASME A112.21.2M |
Roof Drains |
ANSI/ASME A112.18.1M |
Plumbing Supply Fittings |
ANSI/ASME A112.19.2M |
Ceramic Plumbing Fixtures |
ANSI/ASME A112.19.3 |
Stainless Steel Plumbing Fixtures |
ANSI/ASME A112.19.6 |
Hydraulic Performance Requirements for
Water Closets and Urinals |
ANSI/ASME A112.26.1M |
Water Hammer Arresters |
ANSI/ASME A112.36.2M |
Cleanouts |
ANSI/ASME B1.20.1 |
Pipe Threads, General Purpose (Inch) |
ANSI/ASME B16.3 |
Malleable Iron Threaded Fittings: Classes
150 and 300 |
ANSI/ASME B16.4 |
Gray Iron Threaded Fittings Classes
125 and 250 |
ANSI/ASME B16.12 |
Cast Iron Threaded Drainage Fittings |
ANSI/ASME B16.12 |
Cast Copper Alloy Threaded Fittings:
Classes 125 and 250 |
ANSI B16.18 |
Cast Copper Alloy Solder Joint Pressure
Fittings |
ANSI/ASME B16.22 |
Wrought Copper and Copper Alloy Solder-Joint
Pressure Fittings |
ANSI/ASME B16.23 |
Cast Copper Alloy Solder Joint Drainage
Fittings - DWV |
ANSI/ASME B16.24 |
Cast Copper Alloy Pipe Flanges and Flanged
Fittings |
ANSI/ASME B16.26 |
Cast Copper Alloy Fittings for Flared
Copper Tubes |
ANSI/ASME B16.29 |
Wrought Copper and Wrought Copper Alloy
Solder Joint Drainage Fittings - DWV |
ANSI Z21.1 |
Household Cooking Gas Appliances |
ANSI Z21.5.1 |
Gas Clothes Dryers - Volume I, Type
I Clothes Dryers |
ANSI Z21.5.2 |
Gas Clothes Dryers - Volume II, Type
2 Clothes Dryers |
ANSI Z21.8 |
Installation of Domestic Gas Conversion
Burners |
ANSI Z21.10.1 |
Gas Water Heaters Volume I, Storage
Water Heaters With Input Ratings Of 75,000 Btu Per Hour Or Less |
ANSI Z21.10.3 |
Gas Water Heaters - Volume III, Storage
Water Heaters With Input Ratings Above 75,000 Btu per Hour, Circulating
and Instantaneous |
ANSI Z21.11.2 |
Gas-Fired Room Heaters - Volume II,
Unvented Room Heaters |
ANSI Z21.12 |
Draft Hoods |
ANSI Z21.13 |
Gas-Fired Low Pressure Steam and Hot
Water Boilers |
ANSI Z21.19 |
Refrigerators Using Gas Fuel (same as
CSA 1.4) |
ANSI Z21.40.1 |
Gas-Fired, Heat Activated Air Conditioning
and Heat Pump Appliances |
ANSI Z21.40.2 |
Gas-Fired, Work Activated Air-Conditioning
and Heat Pump Appliances (Internal Combustion) |
ANSI Z21.42 |
Gas-Fired Illuminating Appliances |
ANSI Z21.47 |
Gas-Fired Central Furnaces |
ANSI Z21.50 |
Vented Gas Fireplaces |
ANSI Z21.56 |
Gas-Fired Pool Heaters |
ANSI Z21.57 |
Recreational Vehicle Cooking Gas Appliances |
ANSI Z21.58 |
Outdoor Cooking Gas Appliances |
ANSI Z21.60 |
Decorative Gas Burning Appliances for
Installation in Solid-Fuel Burning Fireplaces |
ANSI Z21.63 |
Portable Type Gas Camp Heaters |
ANSI Z21.72 |
Portable Type Gas Camp Stoves (same
as CSA 11.2) |
ANSI Z21.73 |
Portable Type Gas Camp Lights |
ANSI Z21.74 |
Portable Refrigerators for Use With
HD-5 Propane Gas |
ANSI Z21.84 |
Manually Lighted, Natural Gas Decorative
Gas Appliances for Installation in Solid-fuel Burning Fireplaces |
ANSI Z21.86 |
Vented Gas-Fired Space Heating Appliances |
ANSI Z21.88 |
Vented Gas Fireplace Heaters |
ANSI Z21.89 |
Outdoor Cooking Specialty Gas Appliances |
ANSI Z21.97 |
Outdoor Open Flame Decorative Gas Appliances |
ANSI Z83.4 |
Non-Recirculating Direct Gas-Fired Industrial
Air Heaters |
ANSI Z83.7 |
Gas-Fired Construction Heaters (same
as CSA 2.14) |
ANSI Z83.8 |
American National Standard (ANSI Z83.8-2006)
/CSA Standard for Gas Unit Heaters And Gas-Fired Duct Furnaces |
ANSI Z83.11 |
Gas Food Service Equipment |
ANSI Z83.18 |
Recirculating Direct Gas-Fired Industrial
Air Heaters |
ANSI Z83.19 |
Gas-Fired High-Intensity Infrared Heaters |
ANSI Z83.20 |
Gas-Fired Low-Intensity Infrared Heaters |
ANSI Z83.25 |
Direct Gas-Fired Process Air Heaters |
ANSI Z83.26 |
Gas-Fired Outdoor Infrared Patio Heaters |
ANSI Z124.1 |
Plastic Bathtub And Shower Units |
ANSI Z124.2 |
Plastic Shower Units |
ANSI Z124.3 |
Plastic Lavatories |
ANSI Z124.4 |
Plastic Water Closet Bowls And Tanks |
ANSI Z124.6 |
Plastic Sinks |
ASSE 1001 |
Performance Requirements for Atmospheric
Type Vacuum Breakers |
ASSE 1002 |
Performance Requirements for Anti-siphon
Fill Valves for Water Closet Tanks |
ASSE 1003 |
Performance Requirements for Water Pressure
Reducing Valves |
ASSE 1005 |
Performance Requirements for Water Heater
Drain Valves 3/4 Inch Size |
ASSE 1011 |
Performance Requirements for Hose Connection
Vacuum Breakers |
ASSE 1012 |
Performance Requirements for Backflow
Preventers with an Intermediate Atmospheric Vent |
ASSE 1013 |
Performance Requirements for Reduced
Pressure Principle Backflow Preventers and Reduced Pressure Principle
Fire Protection Backflow Preventers |
ASSE 1014 |
Performance Requirements for Backflow
Prevention Devices for Hand-held Showers |
ASSE 1015 |
Performance Requirements for Double
Check Backflow Prevention Assemblies and Double Check Fire Protection
Backflow Prevention Assemblies |
ASSE 1019 |
Performance Requirements for Vacuum
Breaker Wall Hydrants, Freeze Resistant, Automatic Draining Type |
ASSE 1020 |
Performance Requirements for Pressure
Vacuum Breaker Assembly |
ASSE 1024 |
Performance Requirements for Dual Check
Backflow Preventers |
ASSE 1025 |
Performance Requirements for Diverters
for Plumbing Faucets with Hose Spray, Anti-siphon Type, Residential
Applications |
ASSE 1032 |
Performance Requirements for Dual Check
Valve Type Backflow Preventers for Carbonated Beverage Dispensers,
Post Mix Type |
ASSE 1035 |
Performance Requirements for Laboratory
Faucet Backflow Preventers |
ASSE 1047 |
Performance Requirements for Reduced
Pressure Detector Fire Protection Backflow Prevention Assemblies |
ASSE 1048 |
Performance Requirements for Double
Check Detector Fire Protection Backflow Prevention Assemblies |
ASSE 1050 |
Performance Requirements for Stack Air
Admittance Valves for Sanitary Drainage Systems |
ASSE 1051 |
Performance Requirements for Individual
and Branch Type Air Admittance Valves for Sanitary Drainage Systems |
NSF/ANSI Standard 2 |
Food Service Equipment |
NSF/ANSI Standard 4 |
Commercial Cooking, Rethermalization
and Powered Hot Food Holding, and Transport Equipment |
NSF/ANSI Standard 7 |
Commercial Refrigerators and Freezers |
NSF/ANSI Standard 8 |
Commercial Powered Food Preparation
Equipment |
NSF/ANSI Standard 59 |
Mobile Food Carts |
IAS 4-96 |
Outdoor Gas Fireplaces |
AGA Requirement 8-96 |
Gas-Fired Decorative Illuminating Appliances
for Outdoor Installation |
